12.8m Fiberglass Fishing Boat

Technical Specifications of the 12.8m Fiberglass Fishing Boat
Length: 12.8m
Beam: 5.45m
Molded depth: 2.58m
Standard power: 206kw
Crew: 5 persons
Fresh water tank: 800L
Fuel tank: 3000L
Fish deposit capacity: 40CBM

Accessories for the 12.8 Fiberglass Fishing Boat
Section 1
1.1 Hull, decks, superstructure, fish hold and interior joinery are constructed according to ABS or NMR standards.
1.2 Main working deck and forecastle deck both have 6 layers of fiberglass and are built to Norwegian Maritime rules.
1.3 Superstructure and accommodations
The wheelhouse, complete with steering space, galley area, washroom, all necessary doors, and hatches, are made in accordance with Norwegian Maritime rules.
The interior is finished with oak and barker board panels.
1.4 Fishhold
The fishhold, containing three tanks, is built in conformity with Norwegian Maritime standards.

Section 2 Hull Outfitting
2.1 Galley and washroom equipment
(A) Galley stove: propane gas
(B) Galley pump and taps: pressurized, 24volt
(C) Galley water heater: off main engine
(D) TV, DVD: 12V
(E) Refrigerator: 12V DC powered
(F) Galley sink: single tub
(G) Water closet: 24 volts
(H) Wash basin complete with taps: common type
(I) Shower: common type
2.2 Deck fittings and iron work associated with hull
Rudder blade, stock, rudder tube, stuffing box, skeg piece
2.3 Ground tackle
Anchors, cable lines and hawsers are all are equipped according to the Norwegian Maritime Regulations
2.4 Lifesaving and fire fighting equipment
All necessary lifesaving and fire fighting equipment fitted in accordance with the Norwegian Maritime Regulations
2.5 Plumbing
As per Norwegian Maritime approved drawings and specifications
2.6 Hydraulic steering gear
Steering Gear: manual hydraulic
Single helm, single cylinder

Section 3 Mechanical and Associated Piping
3.1 Propulsion engine
A. Main engine: Daewoo MD196T (280HP)
B. Reverse reduction gear: Dongi, speed ratio: 3:1
C. Propeller F/P
D. Shaft
E. Tail shaft: material stainless steel
F. Stern tube c/w bearings material
G. Keel cooler type: "K" copper
H. Electronic engine controls: 2 station plus engine room
3.2 Bilge and associated pumping system
A. Pumps bilge power No. 1 size 1 1/2" capacity
B. Pumps fire hand No. 1 size 1" capacity
C. Pumps wash down No. 1 size 1 1/2" capacity
D. Galvanized or stainless steel pipes for bilge and wash down.

Two pumps
3.3 Tanks and associated piping
A. Tanks (fresh water) No. 1 Mat. S.S. cap each 800 litres
B. Fuel tanks no. as per drawings Mat: steel/resin/gel, cap: 3000 litres (COULD BE 2 FUEL TANKS AS PER REQUEST)
C. Tanks (hydraulic fluid) No. 1 Mat: steel plate cap: each 400 litres
3.4 Natural ventilation system
All supplied and fitted as per Norwegian Maritime approved drawings and specifications and to manufacturers' requirements
3.5 Builder should supply main hydraulic pump and drive device

Section 4 Electrical, Electronic System
4.1 Electrical and electronic equipment
A. 24 Volt D.C.
B. Air intake in engine room
C. Searchlight: No. 1
D. Floodlights: No. 3
E. Batteries: No. 2 for lighting, not for engine start
F. Ground plates No. 1 type: copper plate
G. Radar and stand: make 1 x 24nm
H. Radio: make 1 x vhf dsc
I. Fishing aids (i.e. echo sounder etc.) 1x300 fathom 50/200ktz
J. Navigational aids: Make GPS
K. Additional electronic equipment: electric autopilot 24V DC
4.2 Complete wiring package in accordance with general uniform specifications and approved plans DC 24 Volt

We are a professional 12.8m fiberglass fishing boat manufacturer based in China. We also offer rigid inflatable boat, speed fiberglass boat, luxury fiberglass yacht, inflatable sport boat, inflatable raft, center console fiberglass boat, and more.